Motion Control Products

			100 Series Motion Control systems Complete Package Plug-and-Play Quick and Easy to Install Easy to Use Digital Inputs / Outputs Analog Inputs Up to 4 Axes of Motion Control Motion Control and PLC Functionalities in one Package Externally Controlled Stand-alone Manual Control
100 Series

			300 Series Motion Controler and Driver Card Plug-and-Play 5 Amp BLDC or Brush DC Driver Operates from 12V to 40V 4 Quadrant Operation On Board EEPROM For User Program Storage Stand Alone Operation with no Connection to a PC Pre-wired for Opto-switch inputs Position Velocity and Torque modes Industry standard communications protocol Fully programmable ramps and speeds Quadrature encoder based feedback for position mode
300 Series

			510 Series Servo Motor Control Card Runs DC and Brushless Servo Motors Four Quadrant Regenerative Operation Space Vector Modulation (SVM) Technology Fully Digital State-of-the-art Design Programmable Current, Velocity and Position Loops Gain Settings Fully Configurable Current, Voltage, Position Limits PIDF Velocity Loop Up to 40 Amps Motor Output +20 VDC to +80 VDC Power Supply Protected Against Over Current Built-in Signal Generator, Sinusoidal, Square Wave and Triangular 0 ºC to 70 ºC Operating Temperature Modular 2-Piece Power, Motor, Signal Connector
510 Series

			600 Series Motion Controller Card Stand-alone Externally Controlled Manual Control Up to 4 Axes of Motion Control 16 Digital Inputs 16 Digital Outputs 3 Analog Inputs Optical Encoder Inputs Motion Control and PLC Functionalities in one Package
600 Series

			710 Series Servo Motor Control Card Runs DC Servo Motors with Step and Direction Control Inputs 20 Amp Motor Output +18 VDC to +80 VDC Power Supply PID Closed Loop Operation Quadrature Encoder Feedback Anti-Dithering Circuit Keeps Motor Silent +5VDC, 50 ma Encoder Supply Pulse By Pulse Motor Current Limiting 0 to 20 Amp Current Limit Adjust Range 25 KHz PWM Frequency
710 Series

			800 Series Run DC and Voice Coil Motors with PWM and Direction Control Inputs 20 Amp Motor Output +6 VDC to +30 VDC Power Supply 0 ºC to 70 ºC Operating Temperature Light: 0.36 Oz (10 gm) PWM Frequency up to 40 KHz
800 Series

			900 Series Voice Coil and DC Servo Motor Driver Ultra Small Size Runs Two Motors Simultaneously Low Cost Analog Signal Control Inputs +5 ~ +13.5 VDC
900 Series

			950 Series Voice Coil and DC Servo Motor Driver Ultra Small Size Runs Two Motors Simultaneously Low Cost Analog Signal Control Inputs +5 ~ +13.5 VDC Supplied with Mounting Card for Easy Wire Connection and Mounting Supplied with mounting card for easy wire connection and mounting. This driver does not accept feedback.
950 Series

			1000 Series Converts Two Channels of TTL Differential Signals to Two Channels of Single Ended Signals Jumper Selectable 1 KOhm Pull-ups, 1 KOhm Pull-downs and 120 Ohm Line-to-Line Termination on all Inputs
1000 Series

			Inductive Filter Card Reduces Motor's Ripple Current 10 Amps Peak
IFC-01

			One-micron Optical Encoder Module Small Size, 1.145" (29.1 mm) by 0.551" (14.0 mm) Low Profile, 0.190" (4.8 mm) Low Power Resolution, 0.00004", 1 micron TTL Reference Point Output TTL Differential Quadrature Outputs Single +5 VDC Supply Reflective Device
OEM-001U-01

			Thirty-micron Optical Encoder Module Small Size, 1.145" (29.1 mm) by 0.551" (14.0 mm) Low Profile, 0.190" (4.8 mm) Low Power Resolution, 0.0012", 30 micron TTL Reference Point Output TTL Differential Quadrature Outputs Single +5 VDC Supply Reflective Device
OEM-030U-01

			Optical Encoder Module Cable Used with One-micron Optical Encoder Module Used with Thirty-micron Optical Encoder Module
CBL-01

			Optical Encoder Module Cable Cable, 12 inch (300 mm) Used with 510 Series Used with 600 Series Used with Thirty-micron Optical Encoder Module
CBL-02

			Twenty Six Micron Optical Encoder Low Power Resolution, 26 micron TTL Quadrature Outputs Single +5 VDC Supply Transmissive Device
OEM-250

			Thirteen Micron Optical Encoder Low Power Resolution, 13 micron TTL Quadrature Outputs Single +5 VDC Supply Transmissive Device
OEM-500

			Linear Strip, 500 Lines per Inch
LS-250

			Linear Strip, 500 Lines per Inch
LS-500

			Joysticks Pre-wired Joystick Motor Speed Proportional to the Tilt Angle Three Speed Selection Keys Long Life
JOYSTK

			Switching Power Supply Isolated Outputs and Grounds Withstands 300VAC Surge Input for 5 Seconds Protections: Short circuit / Overload / Over voltage Cooling by free air convection LED indicator for power on All using 105°C long life electrolytic capacitors
PS-125-01

Control Electronics

			One-micron Optical Encoder Module Small Size, 1.145" (29.1 mm) by 0.551" (14.0 mm) Low Profile, 0.190" (4.8 mm) Low Power Resolution, 0.00004", 1 micron TTL Reference Point Output TTL Differential Quadrature Outputs Single +5 VDC Supply Reflective Device
OEM-001U-01	Enlarge

			Thirty-micron Optical Encoder Module Small Size, 1.145" (29.1 mm) by 0.551" (14.0 mm) Low Profile, 0.190" (4.8 mm) Low Power Resolution, 0.0012", 30 micron TTL Reference Point Output TTL Differential Quadrature Outputs Single +5 VDC Supply Reflective Device
OEM-030U-01	Enlarge

			Optical Encoder Module Cable Used with One-micron Optical Encoder Module Used with Thirty-micron Optical Encoder Module
CBL-01	Enlarge

			Optical Encoder Module Cable Cable, 12 inch (300 mm) Used with 510 Series Used with 600 Series Used with Thirty-micron Optical Encoder Module
CBL-02	Enlarge

			Twenty Six Micron Optical Encoder Low Power Resolution, 26 micron TTL Quadrature Outputs Single +5 VDC Supply Transmissive Device
OEM-250	Enlarge

			Thirteen Micron Optical Encoder Low Power Resolution, 13 micron TTL Quadrature Outputs Single +5 VDC Supply Transmissive Device
OEM-500	Enlarge

			Linear Strip, 500 Lines per Inch
LS-250	Enlarge

			Linear Strip, 500 Lines per Inch
LS-500	Enlarge

Linear Brushless Ironless Motors

Features: High Acceleration High Speed High Accuracy Cog Free High Repeatability Independent Multiple Coil Operation with Overlapping Trajectories No Metal-to-Metal Contact, Virtually Maintenance Free Modular Magnet Tracks Trapezoidal or Sinusoidal Commutation Increased throughput, a Function of High Acceleration Exceptional Accuracy Consistent Repeatability Environmentally Friendly Exceptionally High Force per Volume Light Weight-to-Force Ratio Quiet Reduced Wear and Friction Lower Repair and Maintenance Costs High Operating Efficiency Unlimited Stroke Length

Width: 0.82 in  (20.8 mm), Height: 1.50 in (38.1 mm)
Linear Motor Model #	Intermittent Force @ 10% Duty Cycle		Continuous Force @ 25 °C
LBIM-021-01	8.7	lb	2.8	lb
Drawing in PDF	38.7	N	12.2	N

Width: 0.82 in  (20.8 mm), Height: 1.50 in (38.1 mm)
Linear Motor Model #	Intermittent Force @ 10% Duty Cycle		Continuous Force @ 25 °C
LBIM-021-02	16.7	lb	5.3	lb
Drawing in PDF	74.5	N	23.6	N

Width: 0.82 in  (20.8 mm), Height: 1.50 in (38.1 mm)
Linear Motor Model #	Intermittent Force @ 10% Duty Cycle		Continuous Force @ 25 °C
LBIM-021-03	31.6	lb	10.0	lb
Drawing in PDF	140.6	N	44.5	N

Width: 0.82 in  (20.8 mm), Height: 1.50 in (38.1 mm)
Linear Motor Model #	Intermittent Force @ 10% Duty Cycle		Continuous Force @ 25 °C
LBIM-021-04	29.4	lb	18.7	lb
Drawing in PDF	130.8	N	41.4	N

Width: 0.82 in  (20.8 mm), Height: 1.50 in (38.1 mm)
Linear Motor Model #	Intermittent Force @ 10% Duty Cycle		Continuous Force @ 25 °C
LBIM-032-01	29.4	lb	9.3	lb
Drawing in PDF	130.8	N	41.4	N

Width: 0.82 in  (20.8 mm), Height: 1.50 in (38.1 mm)
Linear Motor Model #	Intermittent Force @ 10% Duty Cycle		Continuous Force @ 25 °C
LBIM-032-02	55.3	lb	17.5	lb
Drawing in PDF	246.1	N	77.9	N

Width: 0.82 in  (20.8 mm), Height: 1.50 in (38.1 mm)
Linear Motor Model #	Intermittent Force @ 10% Duty Cycle		Continuous Force @ 25 °C
LBIM-032-03	81.0	lb	25.6	lb
Drawing in PDF	360.4	N	113.9	N

Width: 0.82 in  (20.8 mm), Height: 1.50 in (38.1 mm)
Linear Motor Model #	Intermittent Force @ 10% Duty Cycle		Continuous Force @ 25 °C
LBIM-032-04	108.0	lb	34.0	lb
Drawing in PDF	480.6	N	151.3	N